manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1081 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1081

IP Configuration Command Set

Configuring Dynamic Host Configuration Protocol (DHCP)

Matrix DFE-Platinum and Diamond Series Configuration Guide

12-121

12.2.9.6

ip dhcp pool

Use this command to assign a name to a DHCP server pool of addresses, and to enable DHCP 
address pool configuration mode.

ip dhcp pool

 

name

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command deletes a DHCP address pool:

no ip dhcp pool

 

name

Command Type

Router command.

Command Mode

Global configuration:

 Matrix>Router1(config)#

Command Defaults

None.

Example

This example shows how to assign the name “localpool” as a DHCP address pool, and enable 
configuration mode for that address pool:

name

Specifies a DHCP address pool name.

NOTE:

This must match the previously 

configured name assigned with the ip local pool 
command as described in 

Section 12.2.9.2

.

Matrix>Router1(config)#

ip dhcp pool localpool

Matrix>Router1(config-dhcp-pool)#

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов