Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1010

Страница: 1010 / 1422

IP Configuration Command Set

Configuring PIM

12-50

Matrix DFE-Platinum and Diamond Series Configuration Guide

12.2.7.1

ip pim sparse mode

Use this command to enable Protocol Independent Multicast (PIM) Sparse Mode (SM) on a routing
interface.

ip pim sparse-mode

Syntax Description

None.

Command Syntax of the “no” Form

The

form of this command disables PIM on an interface:

no ip pim sparse-mode

Command Type

Router command.

Command Mode

Interface configuration:

Matrix>Router1(config-if(Vlan 1))#

Command Defaults

None.

Example

This example enables PIM sparse mode on VLAN 1:

Matrix>Router1(config)#

interface vlan 1

Matrix>Router1(config-if(Vlan 1))

#ip pim sparse-mode

«
...
1008
1009
1010
1011
1012
...
»

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1010 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: