manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 343 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 343

Port Configuration Command Set

Configuring Broadcast Suppression

Matrix DFE-Platinum and Diamond Series Configuration Guide

4-83

4.3.9

Configuring Broadcast Suppression

Purpose

To review, disable or set the broadcast thresholds on one or more ports. This limits the amount of 
received broadcast frames that the specified port will be allowed to switch out to other ports. 
Broadcast suppression protects against broadcast storms, leaving more bandwidth available for 
critical data.

Commands 

The commands used to review and configure port broadcast suppression are listed below and 
described in the associated section as shown.

•

show port broadcast (

Section 4.3.9.1

)

•

set port broadcast (

Section 4.3.9.2

)

•

clear port broadcast (

Section 4.3.9.3

)

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов