manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1369 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1369

Security Configuration Command Set

Configuring Access Lists

Matrix DFE-Platinum and Diamond Series Configuration Guide

14-159

14.3.12 Configuring Access Lists

Purpose

To review and configure security access control lists (ACLs), which permit or deny access to 
routing interfaces based on protocol and source IP address restrictions.

Commands

The commands used to review and configure security access lists are listed below and described in 
the associated section as shown:

•

show access-lists (

Section 14.3.12.1

)

•

access-list (standard) (

Section 14.3.12.4

)

•

access-list (extended) (

Section 14.3.12.3

)

•

ip access-group (

Section 14.3.12.4

)

ROUTER:

These commands can be executed when the device is in 

router mode 

only. 

For details on how to enable router configuration modes, refer to 

Section 2.3.3

.

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов