manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1108 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1108

Routing Protocol Configuration Command Set

Configuring RIP

13-6

Matrix DFE-Platinum and Diamond Series Configuration Guide

13.2.2.3

neighbor 

Use this command to instruct the router to send unicast RIP information to an IP address. RIP is 
normally a broadcast protocol. In order for RIP routing updates to reach nonbroadcast networks, the 
neighbor’s IP address must be configured to permit the exchange of routing information.

neighbor ip-address

Syntax Description

Command Syntax of the “no” Form

The “no” form of this

 

command disables point-to-point routing exchanges:

no neighbor ip-address

Command Type

Router command.

Command Mode

Router configuration: 

Matrix>Router1(config-router)#

Command Defaults

None.

Example

This example shows how to instruct the system to exchange routing information with neighbor 
192.5.10.1:

ip-address

Specifies the IP address of a directly connected neighbor 
with which RIP will exchange routing information. 

Matrix>Router1(config)#

router rip

Matrix>Router1(config-router)#

neighbor 192.5.10.1

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов