manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1188 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1188

Routing Protocol Configuration Command Set

Configuring IRDP

13-86

Matrix DFE-Platinum and Diamond Series Configuration Guide

13.2.5.5

ip irdp preference

Use this command to set the IRDP preference value for an interface. This value is used by IRDP to 
determine the interface’s selection as a default gateway address.

ip irdp preference preference

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command resets the interface’s IRDP preference value to the 
default of 

0

: 

no irdp preference

Command Type

Router command.

Command Mode

Interface configuration:

 Matrix>Router1(config-if(Vlan 1))#

Command Defaults

None.

Example

This example shows how to set the IRDP preference value to 80000000 seconds on VLAN 1:

preference

Specifies the value to indicate the interface’s use as a 
default router address. Valid values are 

-2147483648

 to 

2147483647

. The value of 

80000000

 indicates that the 

address, even though it may be advertised, is not to be 
used by neighboring hosts as a default router address.

Matrix>Router1(config)#

interface vlan 1

Matrix>Router1(config-if(Vlan 1))#

ip irdp preference 80000000

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов