manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 239 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 239

Discovery Protocols Command Set

Link Layer Discovery Protocol and LLDP-MED

Matrix DFE-Platinum and Diamond Series Configuration Guide

3-43

3.2.4.10

set lldp hold-multiplier

Use this command to set the time-to-live value used in LLDP frames sent by this device. The 
time-to-live for LLDPDU data is calculated by multiplying the transmit interval by the hold 
multiplier value.

set lldp hold-multiplier

 

multiplier-val

Syntax Description

Command Defaults

None.

Command Type

Switch command.

Command Mode

Read-Write.

Example

This example sets the transmit interval to 20 seconds and the hold multiplier to 5, which will 
configure a time-to-live of 100 to be used in the TTL field in the LLDPDU header.

multiplier-val

Specifies the multiplier to apply to the transmit interval to 
determine the time-to-live value. Value can range from 2 
to 10. Default value is 4.

Matrix(rw)->set lldp tx-interval 20 

Matrix(rw)->set lldp hold-multiplier 5

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов