Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1083

Страница: 1083 / 1422

IP Configuration Command Set

Configuring Dynamic Host Configuration Protocol (DHCP)

Matrix DFE-Platinum and Diamond Series Configuration Guide

12-123

12.2.9.8

dns-server

Use this command to assign one or more DNS servers to DHCP clients.

dns-server

address

[

address2...address8

]

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command deletes the DNS server list:

no dns-server

Command Type

Router command.

Command Mode

Any DHCP configuration mode.

Command Defaults

address2...address8

is not specified, no additional addresses will be configured.

Example

This example shows how to assign a DNS server at 11.12.1.99 to the “localpool” address pool:

address

Specifies the IP address of a DNS server.

address2...
address8

(Optional) Specifies, in order of preference, up to 7
additional DNS server IP address(es).

Matrix>Router1(config)#

ip dhcp pool localpool

Matrix>Router1(config-dhcp-pool)#

dns-server 11.12.1.99

«
...
1081
1082
1083
1084
1085
...
»

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1083 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: