manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1073 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1073

IP Configuration Command Set

Configuring Dynamic Host Configuration Protocol (DHCP)

Matrix DFE-Platinum and Diamond Series Configuration Guide

12-113

DHCP Task List

The CLI commands for DHCP Server provide functionality for: 

1.

Configuring a DHCP local pool for a subnet (required)

2.

Excluding IP addresses not to be assigned to the clients by the DHCP server (optional)

3.

Configuring a DHCP pool (required)

4.

Configuring manual bindings of IP addresses and client hardware addresses (optional)

5.

Configuring a DHCP server boot file (optional)

6.

Monitoring and maintaining DHCP server services (optional)

7.

Enabling DHCP service on a routing interface (required)

DHCP Command Modes

Except for clear and show commands, most DHCP configuration commands can be executed in 
most of the DHCP command modes shown in 

Table 12-12

. CLI examples in this section will show 

a command being executed in one of the appropriate DHCP configuration modes.

.

Table 12-12

DHCP Command Modes 

Mode 

Usage

Access Method

Resulting Prompt

IP Local Pool 
Configuration 
Mode

Configure a local 
address pool as a 
DHCP subnet.

Type

 ip local pool

 

and the local pool 

name

 from Global 

Configuration Mode.

Matrix>Router1
(ip-local-pool)#

DHCP Pool 
Configuration 
Mode

Configure a DHCP 
server address pool.

Type 

ip dhcp pool 

and the address pool 

name

 from Global 

Configuration Mode.

Matrix>Router1
(config-dhcp-pool)#

DHCP Class 
Configuration 
Mode

Configure a DHCP 
client class.

Type 

client-class 

and 

the client class 

name

 

from DHCP Pool or 
Host Configuration 
Mode.

Matrix>Router1
(config-dhcp-class)#

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов