Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 570

Страница: 570 / 1422

Spanning Tree Configuration Command Set

Configuring Spanning Tree Port Parameters

6-118

Matrix DFE-Platinum and Diamond Series Configuration Guide

6.2.2.26

clear spantree adminpoint

Use this

command to reset the administrative point-to-point status of the LAN segment attached to

a Spanning Tree port to auto mode.

clear spantree adminpoint port-string

Syntax Description

Command Defaults

None.

Command Type

Switch command.

Command Mode

Read-Write.

Example

This example shows how to reset point-to-point status to auto on fe.2.3:

port-string

Specifies port(s) on which to reset point-to-point protocol
status. For a detailed description of possible

port-string

values, refer to

Section 4.1.1

Matrix(rw)->

clear spantree adminpoint fe.2.3

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 570 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: