manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1189 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1189

Routing Protocol Configuration Command Set

Configuring IRDP

Matrix DFE-Platinum and Diamond Series Configuration Guide

13-87

13.2.5.6

ip irdp address

Use this command to add additional IP addresses for IRDP to advertise.

ip irdp address ip-address preference

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command clears an IP address from being advertised:

no ip irdp preference ip-address

Command Type

Router command.

Command Mode

Interface configuration:

 Matrix>Router1(config-if(Vlan 1))#

Command Defaults

None.

Example

This example shows how to advertise IP address 183.255.0.162 with a preference of 1 on VLAN 1:

ip-address

Specifies an IP address to advertise.

preference

Specifies the value to indicate the address’ use as a 
default router address. Valid values are 

-2147483648

 to 

2147483647

. The value of 

80000000

 indicates that the 

address, even though it may be advertised, is not to be 
used by neighboring hosts as a default router address.

Matrix>Router1(config)#

interface vlan 1

Matrix>Router1(config-if(Vlan 1))#

ip irdp address 183.255.0.162

 

1

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов