Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 849

Страница: 849 / 1422

Logging And Network Management Command Set

Configuring RMON

Matrix DFE-Platinum and Diamond Series Configuration Guide

11-59

11.2.4.8

set rmon alarm properties

Use this command to configure an RMON alarm entry, or to create a new alarm entry with an
unused alarm index number.

set rmon alarm properties

index

[

interval interval

] [

object

object

] [

type

{absolute

delta}

]

[startup {rising

falling

either}

] [

rthresh

rthresh

] [

fthresh

fthresh

] [

revent

revent

] [

fevent fevent

] [

owner

owner

]

Syntax Description

index

Specifies an index number for this entry. Maximum
number or entries is 50

Maximum value is

65535

interval interval

(Optional) Specifies an interval (in seconds) for RMON
to conduct sample monitoring.

object

object

(Optional) Specifies a MIB object to be monitored.

NOTE:

This parameter is not mandatory for

executing the command, but must be specified
in order to enable the alarm entry configuration.

type absolute

delta

(Optional) Specifies the monitoring method as: sampling
the absolute value of the object, or the difference (delta)
between object samples.

startup rising

falling

either

(Optional) Specifies the type of alarm generated when
this event is first enabled as:

•

Rising - Sends alarm when an RMON event reaches a
maximum threshold condition is reached, for example,
more than 30 collisions per second.

•

Falling - Sends alarm when RMON event falls below a
minimum threshold condition, for example when the
network is behaving normally again.

•

Either - Sends alarm when either a rising or falling
threshold is reached.

rthresh

rthresh

(Optional) Specifies a minimum threshold for causing a
rising alarm.

fthresh

fthresh

Specifies a maximum threshold for causing a falling
alarm.

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 849 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: