Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 910

Страница: 910 / 1422

Logging And Network Management Command Set

Managing Switch Network Addresses and Routes

11-120

Matrix DFE-Platinum and Diamond Series Configuration Guide

11.2.5.17 set movedaddrtrap

Use this command to enable or disable SNMP trap messaging, globally or on one or more ports,
when moved source MAC addresses are detected.

set movedaddrtrap

[

port-string

] {

enable

disable

}

Syntax Description

Command Defaults

port-string

is not

specified, MAC address traps will be globally enabled or

disabled.

Command Mode

Read-Write.

Example

This example shows how to globally enable MAC address traps:

port-string

(Optional) Specifies the port(s) on which to enable or
disable MAC address traps. For a detailed description of
possible

port-string

values, refer to

Section 4.1.1

enable

disable

Enables or disables SNMP trap messaging when moved
source MAC addresses are detected.

Matrix(rw)->

set movedaddrtrap enable

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 910 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: