manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 894 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 894

Logging And Network Management Command Set

Managing Switch Network Addresses and Routes

11-104

Matrix DFE-Platinum and Diamond Series Configuration Guide

11.2.5.6

show ip route

Use this command to display the switch’s IP routing table entries.

show ip route

Syntax Description

None.

Command Defaults

None.

Command Type

Switch command.

Command Mode

Read-Only.

Example

This example shows how to display the IP routing table:

Table 11-12

 provides an explanation of the command output.

Matrix(rw)->

show ip route

                                                       

                                                                                   

ROUTE TABLE                                                                        

Destination      Gateway          Mask      TOS  Flags Refcnt Use      Interface   

------------------------------------------------------------------------------ 

default

12.22.73.13

00000000  0

UC

0 

0

host0       

10.0.0.0

12.22.73.13

ff000000  0

 UC

 

0

host0       

127.0.0.1

127.0.0.1 

00000000  0

UH 

0 

104

lo0 

Table 11-12

show ip route Output Details

Output

What It Displays...

Destination

IP address of the host entry. 

Gateway

MAC address of the destination.

Mask

IP mask of the destination.

TOS

Type of Service setting.

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов