manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1128 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1128

Routing Protocol Configuration Command Set

Configuring RIP

13-26

Matrix DFE-Platinum and Diamond Series Configuration Guide

13.2.2.19 passive-interface

Use this command to prevent RIP from transmitting update packets on an interface.

passive-interface vlan vlan-id

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command disables passive interface:

no passive-interface vlan vlan-id

Command Type

Router command.

Command Mode

Router configuration: 

Matrix>Router1(config-router)#

Command Defaults

None.

Example

This example shows how to set VLAN 2 as a passive interface. No RIP updates will be transmitted 
on VLAN 2:

NOTE:

This command does not prevent RIP from monitoring updates on the interface.

vlan vlan-id

Specifies the number of the VLAN to make a passive 
interface. This VLAN must be configured for IP routing as 
described in 

Section 2.3.1

.

Matrix>Router1(config)#

router rip

Matrix>Router1(config-router)#

passive-interface vlan 2

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов