manualshive.com logo in svg

Xerox WorkCentre 7300 Series, Administrator'S Manual

The Xerox WorkCentre 7300 Series Troubleshooting Manual is a comprehensive user resource designed to address any issues you may encounter with this exceptional product. This manual can be easily downloaded for free from manualshive.com, ensuring prompt resolution for any technical difficulties you may experience.

Share
Download
background image

10

SNMP Configuration 

SNMP (Simple Network Management Protocol) provides a method to remotely monitor and diagnose 
device performance on the network.  Once SNMP has been enabled at the device, SNMP Management 
software, running on a host computer connected to the network, polls the device's agents for operating 
information and responds to traps from the device regarding specific events.  Examples of such events 
might be notifications from the device that it is low on toner, or low on paper.

To view or change the Device's SNMP setting, perform the following steps:

To access SNMP Settings at the Device

1.

Press the 

Log In / Out button

 on the Control Panel.

2.

Press the 

"1" key

 on the numeric keypad five consecutive times.  (This is the factory default 

"password.")

3.

Press 

Enter 

on the touch screen.

4.

Press the 

Machine Status button

 on the Control Panel.

5.

Press the 

Tools tab

.

6.

Press 

Connectivity & Network Setup

.

7.

Press 

Port Settings

.

8.

When the Port Settings menu displays, press the 

SNMP

 selection line.

9.

Press the 

Change Settings

 button in the lower right corner of the Port Settings menu screen.

10. When the SNMP selection menu displays, note that you have only one selection available on a single, 

numbered horizontal line, with the current status of this setting shown.  The Close button in the upper 
right corner of the screen returns you to the Port Settings menu.  After pressing the selection, to 
access available settings press the Change Settings button in the lower right corner of the touch 
screen.

Port Status (SNMP Enablement)

1.

On the SNMP selection menu, press the selection line labeled 

Port Status

.

2.

Press the 

Change Settings

 button.

3.

On the Port Status screen, note which of the two buttons is highlighted as the current setting for SNMP 
Enablement.  The available settings are Enabled or Disabled.  For SNMP to function, it must be set to 
Enabled.

4.

To change settings, press your setting of choice, then press the 

Save

 button.

5.

To exit the screen, without making any changes, press the 

Cancel

 button.

Exiting the SNMP Selection Menu

To exit the SNMP selection menu, which returns you to the Port Settings menu, press the rectangular 

Close

 button in the upper right corner of the touch screen.

Summary of Contents for WorkCentre 7300 Series












































































































































































































Reviews:

No comments

Related manuals for WorkCentre 7300 Series

Canon iPF650 - imagePROGRAF Color Inkjet Printer Basic Manual preview
iPF650 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 40
Canon iP90 - PIXMA Color Inkjet Printer Easy Setup Instructions preview
iP90 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 2
Canon iPF650 - imagePROGRAF Color Inkjet Printer Install Manual preview
iPF650 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 16
Canon iP100 - PIXMA Color Inkjet Printer Setup Instructions preview
iP100 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 2
Canon imageRUNNER ADVANCE C5560 Configuration And Installation Manual preview
imageRUNNER ADVANCE C5560
Brand: Canon Pages: 67
Canon imageRUNNER 3300 Reference Manual preview
imageRUNNER 3300
Brand: Canon Pages: 366
Canon IMAGERUNNER ADVANCE C5051 Getting Started preview
IMAGERUNNER ADVANCE C5051
Brand: Canon Pages: 252
Canon iPF710 - imagePROGRAF Color Inkjet Printer Operations preview
iPF710 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 2
Canon MX490 Series Setup Manual preview
MX490 Series
Brand: Canon Pages: 11
Canon MX490 Series Quick Help Manual preview
MX490 Series
Brand: Canon Pages: 2
Canon Photura 135 Review preview
Photura 135
Brand: Canon Pages: 12
Canon PIXMA Pro9000 Mark II Series Release Note preview
PIXMA Pro9000 Mark II Series
Brand: Canon Pages: 4
Samsung CLP 510N - Color Laser Printer Manual Del Usuario preview
CLP 510N - Color Laser Printer
Brand: Samsung Pages: 270
Samsung Bixolon SRP-270 Integrator'S Manual preview
Bixolon SRP-270
Brand: Samsung Pages: 13
Wang 2241 Reference Manual preview
2241
Brand: Wang Pages: 24
Xerox WorkCentre Pro 421 Brochure & Specs preview
WorkCentre Pro 421
Brand: Xerox Pages: 4
Xerox WorkCentre Pro 412 User Manual preview
WorkCentre Pro 412
Brand: Xerox Pages: 212
Xerox WORKCENTRE PE 220 Evaluator Manual preview
WORKCENTRE PE 220
Brand: Xerox Pages: 8

Brands by name

Popular brands

Load more brands