manualshive.com logo in svg

Xerox WorkCentre 7300 Series, Administrator'S Manual

The Xerox WorkCentre 7300 Series Troubleshooting Manual is a comprehensive user resource designed to address any issues you may encounter with this exceptional product. This manual can be easily downloaded for free from manualshive.com, ensuring prompt resolution for any technical difficulties you may experience.

Share
Download
background image

25

Microsoft (NetBIOS over IP) Networks 

Before You Start

1.

Print a 

Configuration Report

 as stated in the 

Network Connectivity 

section of this guide.

2.

Referring to the report, 

verify that SMB is enabled

.  To enable SMB at the Device, if required, follow 

the procedure below.

3.

Referring to the Configuration Report, 

verify that DNS 

is

 enabled

.  The use of Naming Servers is 

REQUIRED to resolve NetBIOS device names to IP addresses for packet routing over the TCP/IP 
network.

4.

To enable the Device to communicate with the Naming Servers, refer to the instructions supplied in the 
topic "TCP/IP Dynamic Addressing", located in the 

NOS Selection

 section of this guide.

5.

When using WINS or DNS, be sure to refer to your Server Operating System documentation for the 
appropriate procedure to use to enable NetBIOS name to IP address resolution on the Server.

Enabling the SMB Setting at the Device, if required

1.

Press the 

Log In / Out button

 on the Control Panel.

2.

Press the 

"1" key

 on the numeric keypad five consecutive times.  (This is the factory default 

"password.")

3.

Press 

Enter

 on the touch screen.

4.

Press the 

Machine Status button

 on the Control Panel.

5.

Press the 

Tools tab

.

6.

Press 

Connectivity & Network Setup

.

7.

Press 

Port Settings

.

8.

When the Port Settings menu displays, press the 

SMB

 selection line.

9.

Press the 

Change Settings button

 in the lower right corner of the Port Settings menu screen.

10. When the SMB selection menu displays, note that you have only one setting available on a single, 

numbered horizontal line.  Press this selection line.

11. Press the 

Change Settings

 button.

12. On the SMB Port Status screen, note which of the two buttons is highlighted as the current setting for 

SMB Enablement.  The available settings are Enabled or Disabled.  To enable SMB at the device, 
select the 

Enabled

 setting.

13. Press the 

Save

 button on the touch screen, which returns you to the SMB selection menu.  (To exit the 

screen, without making changes, press the 

Cancel

 button.)

14. Exit the SMB selection menu and return to the Port Settings menu by pressing the rectangular 

Close

 

button in the upper right corner of the touch screen.

15. Exit the Port Settings menu by pressing the rectangular 

Close

 button in the upper right corner of the 

Port Settings menu screen.

16. To exit the Tools tab screen, wait several seconds for the Auto Clear service to log you out.

Summary of Contents for WorkCentre 7300 Series












































































































































































































Reviews:

No comments

Related manuals for WorkCentre 7300 Series

SA F1 Series Installation And Operation Manual preview
F1 Series
Brand: SA Pages: 5
NCR 7197 Manual preview
7197
Brand: NCR Pages: 10
Xyron FPO User Manual preview
FPO
Brand: Xyron Pages: 6
Xerox 7700 Setup Manual preview
7700
Brand: Xerox Pages: 2
Xerox 7700 Setup And Quick Reference Manual preview
7700
Brand: Xerox Pages: 40
Xerox 7700 Advanced Features And Troubleshooting Manual preview
7700
Brand: Xerox Pages: 69
Xerox 7700 Install Manual preview
7700
Brand: Xerox Pages: 42
Canon PIXMA MX882 Series Network Setup Manual preview
PIXMA MX882 Series
Brand: Canon Pages: 34
Canon MX470 Getting Started preview
MX470
Brand: Canon Pages: 4
Canon MX470 User Manual preview
MX470
Brand: Canon Pages: 913
Canon Laser Class 700 Series Setup Manual preview
Laser Class 700 Series
Brand: Canon Pages: 30
Canon Laser Class 700 Series Datasheet preview
Laser Class 700 Series
Brand: Canon Pages: 6
Canon Laser Class 700 Series Specification preview
Laser Class 700 Series
Brand: Canon Pages: 6
Canon Laser Class 700 Series Network Manual preview
Laser Class 700 Series
Brand: Canon Pages: 108
Canon PIXMA MX860 series Network Manual preview
PIXMA MX860 series
Brand: Canon Pages: 9
Canon imagePROGRAF iPF9400 Brochure & Specs preview
imagePROGRAF iPF9400
Brand: Canon Pages: 8
Canon PIXMA MX860 series Getting Started Manual preview
PIXMA MX860 series
Brand: Canon Pages: 93
Canon MP980 series Manual preview
MP980 series
Brand: Canon Pages: 20

Brands by name

Popular brands

Load more brands