Vigilantplant TDLS8000 User Manual Download Page 61

Page: 61 / 320

<3. Installation, Wiring, Optical Axis Adjustment, and Piping>

3-16

IM 11Y01D01-01EN

MS-1 MS-2

SV-1

VO(HMI)

SV-2 POW

Internal ground terminal

External ground terminal

24 V DC power supply

Sensor control unit

Terminal C

3.2.3

Connecting to Temperature and Pressure

Transmitters

This section explains the wiring for receiving current signals (4 to 20 mA DC) from a temperature

and pressure transmitters. Connect AI-1 to a pressure transmitter and AI-2 to a temperature

transmitter.
For analog input settings, see “6.3 Analog Input Settings”.

Connection Preparation

To supply power to the transmitters from the TDLS8000, set the switch inside the sensor control

unit to Active AI. To supply power externally, set to Passive AI. If you want to connect to a 4-wire

system pressure meter or thermometer, set to Passive AI.
The factory default setting is Passive AI.

Switch state

Applicable

switch

External

power supply

Power supply from

the TDLS8000

AI-1 (pressure signal)

SW1

Passive AI

Active AI

AI-2 (temperature signal)

SW2

Passive AI

Active AI

Passive AI

SW1

SW2

Sensor control unit

Figure 3.15

SW1 and SW2 settings

3rd Edition: Jun. 10, 2016-00

Summary of Contents for TDLS8000

































































































































































































































































































































Search results

Summary of Contents for TDLS8000

Reviews:

Brands by name

Popular brands

Vigilantplant TDLS8000, User Manual

Search results

Summary of Contents for TDLS8000

Reviews:

Brands by name

Popular brands