Vigilantplant TDLS8000 User Manual Download Page 158

Page: 158 / 320

<8. YH8000 HMI Unit>

8-7

IM 11Y01D01-01EN

8.3.1

Trend Screen Display Items

Item name

Configuration button

Current value

Update pause button

Figure 8.6

Trend Screen

Item name

Shows the item of the displayed trend waveform.

If multiple TDLS8000s are connected, analyzer numbers are added in front of item names

as shown below.

Current value

Shows the current value of the displayed item.

Configuration button

Tapping

at the bottom of the screen shows the trend configuration screen.

Update pause button

Tapping pauses the updating of the trend waveforms. Tapping it again resumes the

updating.

Being updated <=>

Paused

3rd Edition: Jun. 10, 2016-00

Summary of Contents for TDLS8000

































































































































































































































































































































Search results

Summary of Contents for TDLS8000

Reviews:

Brands by name

Popular brands

Vigilantplant TDLS8000, User Manual

Search results

Summary of Contents for TDLS8000

Reviews:

Brands by name

Popular brands