manualshive.com logo in svg

Vigilantplant TDLS8000, User Manual

Share
Download
Vigilantplant TDLS8000 User Manual Download Page 100

 

 

<5.  Startup>

5-9

IM 11Y01D01-01EN

l

  Description of the TDLS8000 selection screen

Analyzer No. column

 

Shows analyzer numbers 1 to 4. You can select a number and assign an IP address to 

connect to the corresponding TDLS8000.

NOTE

If there is only a single TDLS8000 that the YH8000 will connect to, connect it to analyzer number 

1. Otherwise, you will need to reset the display items when displaying the trend waveform.

Analyzer Information column

 

Shows the TDLS8000 IP addresses and tag names. For TDLS8000s that have not been 

connected before, tag names do not appear. If a TDLS8000 is connected but a tag name is 

not assigned, its serial number will be displayed.

Status column

 

Shows the TDLS8000 connection status.

   Connected
   Connecting
   Disconnected

Change IP button

 

Switches to the IP address configuration screen. This button is not available if the 

TDLS8000 is connected.

Connect button

 

Starts a connection with the TDLS8000. This button is available when the TDLS8000 is 

disconnected.

Disconnect button

 

Disconnects from the TDLS8000 that is connected or is in the process of establishing a 

connection.

NOTE

Once a connection is established between the YH8000 and TDLS8000, the connection 

information is saved. Therefore, the next time the power is turned on or after restarting, the 

connection will be established automatically.

NOTE

Up to two YH8000s can connect to a single TDLS8000.

3rd Edition: Jun. 10, 2016-00

Summary of Contents for TDLS8000

































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands