manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual, Page: 98 / 388

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 98

 2 Troubleshooting Procedures 

2.13 Wireless LAN Troubleshooting  

Procedure 2  

Antennas' Connection Check 

The wireless LAN function-wiring diagram is shown below: 

 

Any of the connections may be defective. Disassemble the computer following the steps 
described in Chapter 4, 

Replacement Procedures

, and perform the following checks: 

Check 1 

Make sure the wireless communication switch is “On”. 

If the switch is “Off”, turn it “On”. If the problem still occurs, perform Check 2. 

Check 2 

Make sure wireless LAN card (PCI-E Mini-Card) is firmly connected to the 
CN2600 on the system board. If the connection is loose, connect it firmly and 
perform Procedure 1. If the problem still occurs, perform Check 3. 

Check 3 

Make sure that wireless LAN antenna cables (black and white) are firmly 
connected to the connectors on Wireless LAN card. If wireless LAN antenna 
cables are not connected properly, connect them firmly and perform Procedure 1. 
If the problem still occurs, go to the procedure 3. 

 

2-48 

[CONFIDENTIAL] 

 

TECRA R10 Maintenance Manual (960-708) 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments