manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual, Page: 248 / 388

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 248

4 Replacement Procedures 

4.9  Optical disk drive (DVD-Super Multi drive) 

3.

 

Remove the following 

screws

 and 

ODD REAR BRKT

. 

•

 

M2.0

×

2.7C STEP 

screw     

×

2 

4.

 

Remove the following 

screw

 and 

ODD SIDE BRKT

. 

•

 

M2.0

×

3C   

S-THIN HEAD screw  

 

×

1 

 

 

ODD REAR BRKT 

ODD SIDE BRKT 

M2.0x3C S-THIN HEAD 

M2.0x2.7C STEP 

Optical disk drive 

Figure 4-10 Removing the Optical disk drive (2) 

Installing the Optical disk drive 

To install the Optical disk drive, follow the steps below and refer to Figure 4-9 to 4-10. 

1.

 

Set the 

ODD REAR BRKT 

to the

 optical disk drive

 and secure them with the following 

screws

. 

•

 

M2.0

×

2.7C STEP 

screw     

×

2 

2.

 

Set the 

ODD SIDE BRKT 

to the

 

optical

 

disk drive and secure them with the following 

screw

. 

•

 

M2.0

×

3C   

S-THIN HEAD screw  

 

×

1 

3.

 

Insert the 

ODD ASSY

 into the slot to connect it to the connector on the system board and 

secure optical disk drive assembly with the following 

screws

. 

•

 

M2.5

×

6C   

FLAT HEAD screw   

 

×

2 

CAUTION:  Drive the screws in the order shown in the Figure 4-9. 

4-22 

[CONFIDENTIAL] 

TECRA R10 Maintenance Manual (960-708) 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments