manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 150

3 Tests and Diagnostics  

3.13 Hard Disk Test   

3-28 

 [CONFIDENTIAL]  

TECRA R10 Maintenance Manual (960-708) 

Subtest 04 

Cross talk & peak shift 

This subtest writes eight types of worst pattern data (listed below) to a 
cylinder, then reads the data while moving from cylinder to cylinder. (Test the 
data interference in the neighbor track) 

Worst pattern data 

Cylinder 

‘B5ADAD’ 0 

cylinder 

‘4A5252’ 1 

cylinder 

‘EB6DB6’ 2 

cylinder 

‘151149’ 3 

cylinder 

’63B63B’ 4 

cylinder 

‘9C49C4’ 5 

cylinder 

‘2DB6DB’ 6 

cylinder 

‘D25114’ 7 

cylinder 

Subtest 05 

Partial Read 

 

This subtest reads 1GB data that is in minimum, middle and maximum 
address of the HDD area. 

Subtest 06 

Write specified address 

This subtest writes specified data to a specified cylinder and head on the 
HDD. 

Subtest 07 

Read specified address 

This subtest reads data, which has been written to a specified cylinder and 
head on the HDD. 

Subtest 08 

Sequential write 

This subtest writes specified 2-byte data to all of the cylinders on the HDD. 

Subtest 09 

W-R-C specified address 

This subtest writes data to a specified cylinder and head on the HDD, then 
reads the data and compares it to the original data. 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands