Toshiba Tecra R10 Maintenance Manual Download Page 214

Page: 214 / 388

3 Tests and Diagnostics

3.32 SETUP

Configuration

This option lets you set the device configuration.

All Devices

BIOS sets all devices.

Setup by OS

Initializes devices, which is needed to load an operating
system. Operating system initializes other devices.
(Default)

NOTE: 1. When using installed OS, selecting “Setup by OS” is recommended.

2. When executing test programs, be sure to select “ALL Device”. And after

the test end, select “Setup by OS”.

Battery

(a)

Battery Save Mode

This option is used to select

Full Power

Low Power

User Setting

of the battery

save mode. When you select the battery save mode, the followings will appear.

Full

Power

The following shows full power settings.

Low

Power

The following shows low power settings.

NOTE: Display of the LCD

Brightness will be changed in the condition below:

(*1) Operating the battery

(*2) Using the AC adapter

User Setting

Use this option to set the battery save parameters on

the

sub-window,

BATTERY SAVE OPTIONS

Battery Save Options

3-92 [CONFIDENTIAL]

TECRA R10 Maintenance Manual (960-708)

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands

Toshiba Tecra R10, Maintenance Manual

Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands