Toshiba Tecra R10 Maintenance Manual Download Page 260

Page: 260 / 388

4 Replacement Procedures

4.14 Wireless LAN card

4.14 Wireless LAN card

CAUTION: Do not touch the connectors on the Wireless LAN card. Debris on the connectors

may cause the wireless LAN card access problems.

Removing the Wireless LAN card

To remove the wireless LAN card, follow the steps below and refer to Figure 4-19.

Disconnect two Wireless

LAN antenna cable

from the wireless LAN card.

Remove the following

screws

securing wireless LAN card.

•

M2.0

S-THIN

HEAD

screw

Disconnect the Wireless

LAN card

from the connector

CN2600

on the system board.

M2.0

4B S-THIN HEAD

Wireless LAN card

CN2600

Wireless LAN antenna cable

Figure 4-19 Removing the Wireless LAN card

4-34

[CONFIDENTIAL]

TECRA R10 Maintenance Manual (960-708)

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands

Toshiba Tecra R10, Maintenance Manual

Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands