Toshiba Tecra R10 Maintenance Manual Download Page 24

Page: 24 / 388

1 Hardware Overview

1.2 System Unit Block Diagram

1-10

[CONFIDENTIAL]

TECRA R10 Maintenance Manual (960-708)

•

North Bridge Intel Cantiga GS

Meorom Processor System Bus Supports

PCI Express Based Graphics Interface

System Memory supports :DDR2-667

／

DDR2-800, 4GB max.

DMI(Direct Media Interface: x4/x2, ASPM L0s, L1 states support)

Power management control (DPST 4.0)

•

South Bridge ICH9M-E(SFF)

-PCI Local Bus Specification, Revision 2.3-compliant with support for

33MHz PCI operations

-PCI slots (supports up to 4 Req/Gnt pairs)

-PCI Express (6 PCI Express root ports)

-ACPI 3.0b compliant

-Enhanced DMA Controller, Interrupt Controller, and Timer Functions

-Integrated Serial ATA Host Controller (4 ports)

-USB host interface with support for 12 USB ports; 6 UHCI host

controllers; 2 EHCI high-speed USB 2.0 Host Controller

-System Management Bus (SMBus) Specification, Version 2.0 with

additional support for I2C devices

-Intel High Definition Audio Interface

-Supports Audio Codec ’97, Revision 2.3 specification or HD Audio

-Low Pin Count (LPC) interface

-Firmware Hub (FHW) interface support

-Alert On LAN (AOL)

-Support for Intel® AMT 4.0

-Support for Integrated Trusted Port module 1.2

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands

Toshiba Tecra R10, Maintenance Manual

Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands