manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 262

4 Replacement Procedures 

4.15  RTC battery 

4.15 RTC battery 

CAUTION:  Risk of explosion if battery is replaced by an incorrect type. Dispose of used 

batteries according to the laws and ordinances of your local authority. 

Removing the RTC battery 

To remove the RTC battery, follow the steps below and refer to Figure 4-20-1 to 4-20-2. 

1.

 

Disconnect the 

ODD FPC

 from connector 

CN1950

 on the system board and remove the 

following screw to remove the 

ODD CONN HOLD BRKT

 from the BASE ASSY. 

•

 

M2.5

×

4C 

  FLAT 

HEAD 

screw 

  

×

1 

2.

 

Disconnect the 

RTC battery harness

 from the connector 

CN9300 

on the system board. 

3.

 

Remove the 

INSU RTC BATT

 fixed to the 

SD board

 with the double-sided tape. 

4.

 

Open the cover of INSU RTC BATT while peeling adhered portion with the double-sided 
tape and remove the 

RTC battery

 from the INSU RTC BATT. 

 

RTC battery 

RTC battery

 

harness 

INSU RTC BATT 

CN9300

CN1950

ODD CONN 

HOLD BRKT 

M2.5x4C FLAT HEAD 

SD board 

ODD FPC 

Figure 4-20-1 Removing the RTC battery (1) 

4-36 

[CONFIDENTIAL] 

TECRA R10 Maintenance Manual (960-708) 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands