manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 71

2.4 System Board Troubleshooting   

2  Troubleshooting Procedures  

Procedure 2 

Debugging Port Check (Boot Mode) 

Check the D port status by a serial port test. The tool for serial port test is shown below. 

 

 

Figure 2-2  Debug port (Boot mode) error status 

The test procedures are follows: 

 

1.

 

Connect the debug port test cable to the connector CN3490 of the system board. For 
disassembling to connect the test cable, refer to Chapter 4. 

2.

 

Connect the debug port test cable and RS-232C cross-cable to the test board. 

3.

 

Connect the RS-232C Cross-cable to the PC that displays the test results. 

 

4.

 

Boot the computer in MS-DOS mode. 

5.

 

Execute GETDPORT.COM in the text menu in CPU REAL mode. (Insert the FD for 
starting D port into FDD and input “FD starting drive:>dport”.) 

The D port status is displayed in the following form; 

TECRA R10 Maintenance Manual (960-708) 

[CONFIDENTIAL] 

2-21 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands