Home
/
Toshiba
/
Tecra R10
/
Maintenance Manual

Toshiba Tecra R10, Maintenance Manual

Share

Page: 185 / 388

Toshiba Tecra R10 Maintenance Manual Download Page 185

3.26

Wireless LAN Test Program (Atheros): UNot UsedU

3 Tests and Diagnostics

Check of the antenna connection

1.

Confirm that the icon for wireless LAN appears at the lower right of the screen under
the circumstances the wireless LAN communication is available. (It is no problem if a
cross is shown on the icon.)

2.

Double-click the icon. If the computer finds any AP (Access Point), the antenna
marks like as follows will appear. It shows the antenna cables are surely connected to
the wireless LAN card.

3.

The following message will appear if the antenna cables are not connected to the
wireless LAN card or no available access point is found. In this case, check the
antenna cable connection to the wireless LAN card by disassembling the computer
following the steps described in Chapter 4, Replacement Procedures.

TECRA R10 Maintenance Manual (960-708)

[CONFIDENTIAL]

3-63

«
...
183
184
185
186
187
...
»

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands