manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 100

 2 Troubleshooting Procedures 

2.14 Bluetooth Troubleshooting  

2-50 

[CONFIDENTIAL] 

 

TECRA R10 Maintenance Manual (960-708) 

2.14 Bluetooth Troubleshooting 

This section describes how to determine if the computer’s Bluetooth is functioning properly.  
Perform the steps below starting with Procedure 1 and continuing with the other procedures 
as required. 

Procedure 1:  Diagnostic Test Program Execution Check 

Procedure 2:  Connection Check 

Procedure 3:  Replacement Check 

Procedure 1  

Diagnostic Test Program Execution Check 

Make sure the wireless switch on the left side of the computer is turned “On”. If it is not, 
slide the switch toward the back of the computer to turn it on. 

Check 1 

Execute Bluetooth test program. Perform the test following the instructions 
described in Chapter 3, Bluetooth Test Program. You will need a second computer 
that can communicate by the Bluetooth. 
If the computer passes the test, the function is correctly working. If the computer 
does not pass the test, go to check 2. 

Check 2 

The Bluetooth module may be defective or damaged. Replace it with a new one. 
Then perform the test program again. 

 

If the computer still does not pass the test, go to Procedure 2. 

 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands