Toshiba Tecra R10 Maintenance Manual Download Page 240

Page: 240 / 388

4 Replacement Procedures

4.4 ExpressCard

4.4 ExpressCard

Removing the ExpressCard

To remove the ExpressCard, follow the steps below and refer to Figure 4-3

CAUTION: Insert or remove an ExpressCard in accordance with any instructions in the

ExpressCard manual or the manuals of the computer system you are using.

Press the

ExpressCard

in order to eject the ExpressCard partially out of the computer.

Grasp the ExpressCard and pull it out.

ExpressCard

Figure 4-3 Removing the ExpressCard

Installing the ExpressCard

To install the ExpressCard, follow the steps below and refer to Figure 4-3.

Insert the

ExpressCard

into the ExpressCard slot.

Press ExpressCard carefully to ensure a firm connection.

4-14

[CONFIDENTIAL]

TECRA R10 Maintenance Manual (960-708)

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Toshiba Tecra R10, Maintenance Manual, Page: 240 / 388

Search results

Summary of Contents for Tecra R10

Reviews: