manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual, Page: 104 / 388

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 104

2  Troubleshooting Procedures  

2.15 Sound Troubleshooting 

2-54 

 [CONFIDENTIAL] 

 

TECRA R10 Maintenance Manual (960-708) 

As the connection may be defective, disassemble the computer and check each connection. If 
the problem still occurs, go to Procedure 3. 

Procedure 3 

Replacement Check  

‰

 

If headphone does not work properly, perform check 1. 

‰

 

If external microphone does not work properly, perform check 2.  

‰

 

If speaker does not work properly, perform check 3. 

‰

 

If internal microphone does not work properly, perform check 4. 

 

Check 1 

Headphone may be faulty. Replace it with a new one following the steps in 
Chapter 4, 

Replacement Procedures

. If the problem still occurs, perform Check 5. 

Check 2 

External microphone may be faulty. Replace it with a new one following the steps 
in Chapter 4, 

Replacement Procedures

. If the problem still occurs, perform Check 

5 

Check 3 

Speaker may be faulty. Replace it with a new one following the steps in Chapter 4, 

Replacement Procedures

. If the problem still occurs, perform Check 5 

Check 4 

Internal microphone may be faulty. Replace it with a new one following the steps 
in Chapter 4, 

Replacement Procedures

. If the problem still occurs, perform Check 

5 

Check 5 

Sound/USB board or cable may be faulty. Replace it with a new one following the 
instructions in Chapter 4, 

Replacement Procedures

. If the problem still occurs, 

perform Check 6 

Check 6 

System board may be faulty. Replace it with a new one following the instructions 
in Chapter 4, 

Replacement Procedures

. 

 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments