manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 267

4.16  DC-IN HARNESS/RJ45 WIRE HARNESS 

4 Replacement Procedures 

TECRA R10 Maintenance Manual (960-708) 

[CONFIDENTIAL] 

4-41 

Installing the DC-IN HARNESS/RJ45 WIRE HARNESS 

To install the DC-IN HARNESS/RJ45 WIRE HARNESS, follow the steps below and refer to 
Figure 4-21 to 4-23. 

1.

 

Set the 

RJ45 WIRE HARNESS 

into the HARNESS HOLDER R. 

2.

 

Set the 

HARNESS HOLDER R

 in the slot in place and secure it with following screws. 

•

 

M2.5

×

6C 

  FLAT 

HEAD 

screw 

  

×

1 

3.

 

Arrange the 

3G antenna cables

, 

Wireless LAN antenna cables

, 

RJ45 WIRE 

HARNESS

 and 

CAMERA HARNESS

 on the HARNESS HOLDER R. 

4.

 

Connect the two 

3G antenna cables

 to the terminals on the 3G card, 

RJ45 WIRE 

HARNESS

 to the connector 

CN4100

 on the system board and 

CAMERA HARNESS

 to 

the connector 

CN9540

 on the system board. 

5.

 

Stick the 

acetate tape

 in place. 

6.

 

Set the 

DC-IN HARNESS

 in the slot in place and connect the 

DC-IN HARNESS

 to the 

connector 

CN8800

 on the system board. 

 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands