Toshiba Tecra R10 Maintenance Manual Download Page 169

Page: 169 / 388

3.20 ONLY ONE TEST

3 Tests and Diagnostics

Subtest 7

Acceleration sensor

This subtest detects and corrects the each axis (X, Y, Z).

NOTE: Make sure that this subtest is executed on the following condition:

1. Flat desk with vertical plane to get the stability of machine.

2. The vertical wall or plane is necessary.

3. Prevent the machine from shake or shock.

Vertical plane

Flat desk

Set the machine
against the vertical plane
with the Front upward

The figure below shows the name and position of each side.

TECRA R10 Maintenance Manual (960-708) [CONFIDENTIAL]

3-47

Right side

Left side

Back

Front

Top
(heaven surface)

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands

Toshiba Tecra R10, Maintenance Manual

Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands