manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 102

 2 Troubleshooting Procedures 

2.14 Bluetooth Troubleshooting  

2-52 

[CONFIDENTIAL] 

 

TECRA R10 Maintenance Manual (960-708) 

Procedure 3  

Replacement Check 

The Bluetooth antenna, Bluetooth module, sound board and system board are connected to 
the circuits. Any of these components may be damaged. Refer to Chapter 4, 

Replacement 

Procedures,

 for instructions on how to disassemble the computer and then perform the 

following checks: 

Check 1 

The Bluetooth module may be defective or damaged. Replace the Bluetooth 
module with a new one following the steps in Chapter 4, 

Replacement Procedures

. 

If the Bluetooth is still not functioning properly, perform Check 2. 

Check 2 

The Bluetooth module FPC may be defective or damaged. Replace the Bluetooth 
module FPC with a new one following the steps in Chapter 4, 

Replacement 

Procedures

. If the Bluetooth is still not functioning properly, perform Check 3. 

Check 3 

The system board may be defective or damaged. Replace the system board with a 
new one following the steps in Chapter 4, 

Replacement Procedures

.  

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands