Toshiba Tecra R10 Maintenance Manual Download Page 249

Page: 249 / 388

4.10 Keyboard

4 Replacement Procedures

4.10 Keyboard

Removing the Keyboard

To remove the keyboard, follow the steps below and refer to Figure 4-11 to 4-12.

CAUTION: As the keytop may fall out, when handling the keyboard always hold it by the

frame and do not touch the keytop.

Turn over the computer and open the display.

Insert your fingers into the

slit

and remove

KB HOLDER

while releasing the latches.

Remove the following

screws

securing the keyboard.

•

M2.0

BIND

screw

Lift the top edge of the

keyboard

and turn the keyboard face down on the palm rest

portion of COVER ASSY.

KB HOLDER

Slit

M2.0x4B BIND

Keyboard

Figure 4-11 Removing the keyboard (1)

TECRA R10 Maintenance Manual (960-708)

[CONFIDENTIAL]

4-23

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands

Toshiba Tecra R10, Maintenance Manual

Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands