Toshiba Tecra R10 Maintenance Manual Download Page 283

Page: 283 / 388

4.22 DC FAN

4 Replacement Procedure

TECRA R10 Maintenance Manual (960-708)

[CONFIDENTIAL]

4-57

Secure the

H SINK PLT

and

VGA PLATE HOLDER

(only for external graphics

chip model) with the following

screw

•

M1.6

4C OTHER screw

•

M1.6

4C OTHER screw

2 (for external Graphics chip)

NOTE: When securing the H SINK PLT and VGA PLATE HOLDER, be sure to secure

the screws in the order of the number marked on the plate.

Set the

DC FAN assembly

in place and connect the

DC FAN harness

to the

connector

CN8771

on the system board.

10.

Fix the

RGB harness

to the DC FAN with

INSU RGB HNS

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands

Toshiba Tecra R10, Maintenance Manual

Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands