Home
/
Toshiba
/
Tecra R10
/
Maintenance Manual

Toshiba Tecra R10, Maintenance Manual

Share

Page: 238 / 388

Toshiba Tecra R10 Maintenance Manual Download Page 238

4 Replacement Procedures

4.2 Battery pack

4-12

[CONFIDENTIAL]

TECRA R10 Maintenance Manual (960-708)

Installing the Battery pack

To install the battery pack, follow the steps below and refer to Figure 4-1.

CAUTION: There is a danger that the lithium ion battery pack may explode if not fitted,

operated, handled, or disposed correctly. Dispose always the used battery pack
in accordance with the laws and ordinances of your local authority.
Use only the batteries approved by Toshiba.

NOTE: Check the battery’s terminals visually. If they are dirty, wipe them clean with a dry

cloth.

1.

Turn off the power of the computer.

2.

Disconnect the AC adapter and all other external devices from the computer.

3.

Turn the computer face down.

4.

Install the

battery pack

into the battery slot.

5.

Make sure the battery is locked.

«
...
236
237
238
239
240
...
»

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands