Toshiba Tecra R10 Maintenance Manual Download Page 86

Page: 86 / 388

2 Troubleshooting Procedures

2.7 Keyboard Troubleshooting

2-36

[CONFIDENTIAL]

TECRA R10 Maintenance Manual (960-708)

2.7 Keyboard

Troubleshooting

To check if the computer’s keyboard is malfunctioning or not, follow the troubleshooting
procedures below as instructed.

Procedure 1: Diagnostic Test Program Execution Check

Procedure 2: Connector Check and Replacement Check

Procedure 1

Diagnostic Test Program Execution Check

Execute the Keyboard Test (DIAGNOSTIC TEST) and Pressed key display test (ONLY
ONE TEST) in the Diagnostic Program. Refer to Chapter 3,

Tests and Diagnostics

, for more

information on how to perform the test program.

If an error occurs, go to Procedure 2. If an error does not occur, keyboard is functioning
properly.

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands

Toshiba Tecra R10, Maintenance Manual

Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands