manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 299

4.28  TOUCH PAD/Fingerprint sensor board 

4 Replacement Procedure 

TECRA R10 Maintenance Manual (960-708) 

[CONFIDENTIAL] 

4-73 

Install the TOUCH PAD /Fingerprint sensor board 

To install the TOUCH PAD /Fingerprint sensor board, follow the steps below and refer to 
Figure 4-42 to 4-45. 

1.

 

Stick a new 

TP SPILL CUSHION 

on a new 

Fingerprint sensor board

 in place.  

2.

 

Stick a new 

D STICK TAPE TP 

in place. 

3.

 

Stick the Fingerprint sensor board in place on the COVER ASSY and secure it with 
the following 

screw

s. 

•

 

M2.0

×

4C   S-THIN HEAD   

×

2 

4.

 

Set the 

TP BTN COV ASSY

 in place while engaging the latches. 

5.

 

Turn over the COVER ASSY. 

6.

 

Stick a new 

TOUCH PAD

 in place. 

7.

 

Set the 

TPAD PLT ASSY

 while engaging the latch and secure it with following 

screw. 

•

 

M2.5

×

4C 

 FLAT 

HEAD 

  

×

 1  

8.

 

Connect the 

TP FFC

 to the connector on the 

TOUCH PAD 

and

 Fingerprint sensor 

board

. 

9.

 

Connect the 

Fingerprint sensor board FFC

 to the connector on the Fingerprint 

sensor board. 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands