manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual, Page: 58 / 388

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 58

 2  Troubleshooting Procedures  

2.3 Power Supply Troubleshooting   

2-8  

[CONFIDENTIAL] 

TECRA R10 Maintenance Manual (960-708) 

2.3 Power 

Supply 

Troubleshooting 

The power supply controller controls many functions and components. To determine if the 
power supply is functioning properly, start with Procedure 1 and continue with the other 
Procedures as instructed. The procedures described in this section are: 

Procedure 1:  Power Status Check 

Procedure 2:  Error Code Check 

Procedure 3:  Connection Check 

Procedure 4:  Charging Check 

Procedure 5:  Replacement Check 

Procedure 1 

Power Status Check 

The following icons indicate the power supply status: 

‰

 

Battery icon 

‰

 

DC IN icon 

The power supply controller displays the power supply status with the Battery icon and the 
DC IN icon as listed in the tables below. 

Table 2-1  Battery icon 

Battery icon 

Power supply status 

Lights orange 

Battery is charged and the external DC is input. It has no 
relation with ON/OFF of the system power. 

Lights blue 

Battery is fully charged and the external DC is input. It has 
no relation with ON/OFF of the system power. 

Flashes orange 

Battery charge is low. The AC adaptor must be connected 
to recharge the battery. 

Blinks orange 
(even intervals) 

The battery level is low while the system power is ON.  

Blinks orange once 
(at being switched on) 

The system is driven by only a battery and the battery level 
is low.  

Doesn’t light 

Any condition other than those above. 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments