manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 241

4.5  SD/SDHC memory card 

4 Replacement Procedures 

4.5  SD/SDHC memory card 

Removing the SD/SDHC memory card 

To remove the SD/SDHC memory card, follow the steps below and refer to Figure 4-4. 

CAUTION:  Insert or remove a SD/SDHC memory card in accordance with any instructions 

in the SD/SDHC memory card manual or the manuals of the computer system 
you are using. 

1.

 

Press the 

SD/SDHC memory card

 and release it to pop the card out. 

2.

 

Grasp the SD/SDHC memory card and pull it out. 

 

SD/SDHC memory card

Figure 4-4  Removing the SD/SDHC memory card 

Installing the SD/SDHC memory card 

To install the SD/SDHC memory card, follow the steps below and refer to Figure 4-4. 

1.

 

Insert the 

SD/SDHC memory card 

in the card slot and push it carefully to ensure a firm 

connection. 

TECRA R10 Maintenance Manual (960-708) 

[CONFIDENTIAL] 

4-15 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands