manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 255

4.11  BASE ASSY 

4 Replacement Procedures 

TECRA R10 Maintenance Manual (960-708) 

[CONFIDENTIAL] 

4-29 

Installing the BASE ASSY 

To install the BASE ASSY, follow the steps below and refer to Figure 4-13 to 4-15. 

1.

 

Set the 

BASE ASSY

 in place while setting the RGB connector side first. (See figure 4-

15).  

2.

 

Secure the BASE ASSY with the following

 screw

s. 

•

 

M2.5

×

6C   

FLAT HEAD screw   

×

13 (No description) 

•

 

M2.5

×

4C   

FLAT HEAD screw   

×

1 (Described as “A” in the figure) 

CAUTION:  Drive the fourteen screws in the order shown in the Figure 4-15. 

3.

 

Connect the 

ExpressCard slot FPC

 to the connector 

CN2520

 on the system board.  

4.

 

Turn the computer upside down. 

5.

 

Connect the 

LCD harness

 to the connector 

CN5000

 on the system board. 

6.

 

Stick the 

INSU LCD HNS UP

 on the 

COVER ASSY

 in place. 

CAUTION:  Do not reuse the removed INSU LCD HNS UP. Use a new one

.

 

7.

 

Secure the BASE ASSY with following 

screws

. 

•

 

M2.5

×

6C   

FLAT HEAD screw   

×

2  

CAUTION:  Drive the two screws in the order shown in the Figure 4-13. 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands