Toshiba Tecra R10 Maintenance Manual Download Page 155

Page: 155 / 388

3.16 Expansion Test

3 Tests and Diagnostics

TECRA R10 Maintenance Manual (960-708) [CONFIDENTIAL]

3-33

Subtest 02

RGB monitor ID

NOTE: To execute this subtest, monitor supporting EDID (Extended Display

Identification Data) is required.

Connect a wraparound connector to CRT monitor for the test of ID acquisition.
This subtest is executed by using VESA command.

CAUTION: It becomes NG because the priority is given to the internal monitor in a

simultaneous display mode.

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands

Toshiba Tecra R10, Maintenance Manual

Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands