manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 67

2.3 Power Supply Troubleshooting   

2  Troubleshooting Procedures  

TECRA R10 Maintenance Manual (960-708) 

[CONFIDENTIAL] 

2-17 

Procedure 5 

Replacement Check 

The power is supplied to the system board by the AC adapter. If either the AC adapter or the 
system board was damaged, perform the following Checks. 

To disassemble the computer, follow the steps described in Chapter 4, 

Replacement 

Procedures

.  

When AC adapter is connected:  

Check 1 

AC adapter may be faulty. Replace the AC adapter with a new one. If the problem 
still occurs, perform Check 2. 

Check 2 

System board may be faulty. Replace the system board with a new one. 

 

When AC adapter is not connected: 
(When driving with battery pack) 

Check 1 

Battery pack may be faulty. Replace it with a new one. If the problem still occurs, 
perform Check 2. 

Check 2 

System board may be faulty. Replace it with a new one. 

 

 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands