manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual, Page: 95 / 388

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 95

2.11 Optical Drive Troubleshooting 

2  Troubleshooting Procedures 

Procedure 2 

Connector Check and Replacement Check

 

The optical drive (DVD Super Multi drive) is connected to the system board. The connectors 
may be disconnected from the system board or may be damaged. Disassemble the computer 
following the steps described in Chapter 4, 

Replacement Procedures

 and perform the 

following checks: 

Check 1 

The connection of Optical drive system is shown in the following figure. 

 

If any of the connections is loose, reconnect firmly and repeat Procedure 1. If 
there is still an error, go to Check 2. 

Check 2 

The Optical drive (SATA ODD) may be defective or damaged. Replace the drive 
with a new one. If there is still an error, go to Check 3. 

Check 3 

The SATA ODD FPC may be defective or damaged. Replace the drive with a new 
one. If there is still an error, go to Check 4. 

Check 4 

Replace the system board with a new one following the steps in Chapter 4, 

Replacement Procedures

. 

TECRA R10 Maintenance Manual (960-708) 

 

 [CONFIDENTIAL] 

 2-45 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments