Toshiba Tecra R10 Maintenance Manual Download Page 279

Page: 279 / 388

4.22 DC FAN

4 Replacement Procedure

4.22 DC FAN

CAUTION: Do not apply pressure to the DC FAN.

Removing the DC FAN

To remove the DC FAN, follow the steps below and refer to Figure 4-30 to 4-32.

Remove the following

screw

to remove

H SINK PLT

and screws fixing the

VGA

PLATE HOLDER

(only for external graphics chip model).

•

M1.6

4C OTHER screw

•

M1.6

4C OTHER screw

2 (for external Graphics chip)

NOTE: When removing the H SINK PLT or VGA PLATE HOLDER, be sure to remove

the screws in the reverse order of the number marked on the heat.

Disconnect the

DC FAN harness

from the connector

CN8771

on the system board.

Peel the

INSU RGB HNS

fixing the RGB harness to DC FAN and remove the

FAN assembly

from the system board.

M1.6x4C OTHER

INSU RGB HNS

CN8771

DC FAN harness

DC-FAN assembly

H SINK PLT

Figure 4-30 Removing the DC FAN (1)

TECRA R10 Maintenance Manual (960-708)

[CONFIDENTIAL]

4-53

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands

Toshiba Tecra R10, Maintenance Manual

Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands