manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 277

4.21  RGB HARNESS 

4 Replacement Procedure 

4.21 RGB HARNESS 

Removing the RGB HARNESS 

To remove the RGB HARNESS, follow the steps below and refer to Figure 4-29. 

1.

 

Remove the following 

screw

s

 

to remove the 

RGB HARNESS

 from the slot. 

•

 

#4-40

×

5C  

UNIFIED screw   

×

2 

2.

 

Peel the

 

INSU RGB HNS

 

fixing the

 

RGB HARNESS to the DC-FAN. 

3.

 

Disconnect the

 

RGB HARNESS from the connector 

CN9510

 on the system board. 

 

RGB HARNESS

#4-40x5C UNIFIED 

INSU RGB HNS 

CN9510 

Figure 4-29 Removing the RGB HARNESS 

TECRA R10 Maintenance Manual (960-708) 

[CONFIDENTIAL] 

4-51 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands