manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 96

 2 Troubleshooting Procedures 

2.12 LAN Troubleshooting  

2.12 LAN Troubleshooting 

To check if the computer’s LAN is malfunctioning or not, follow the troubleshooting 
procedures below as instructed. 

Procedure 1:   Diagnostic Test Program Execution Check 

Procedure 2:   Connector Check and Replacement Check 

Procedure 1 

Diagnostic Test Program Execution Check 

Execute LAN test in the LAN/Modem/Bluettoth/IEEE1394 test program. Refer to Chapter 3, 

Tests and Diagnostics

 for more information on how to perform the test program. 

If any error is detected by the test, go to Procedure 2. 

Procedure 2 

Connector Check and Replacement Check 

LAN cable is connected to system board. If LAN malfunctions, the connection of the cable 
and board may be defective. Otherwise, they may be faulty. 

Check 1 

Make sure LAN cable is firmly connected to the LAN jack on the system board. If 
the problem still occurs, perform Check 2. 

 

Check 2 

LAN cable may be faulty. Replace it with a new one. If the problem still occurs, 
perform Check 3. 

Check 3 

System board may be faulty. Replace it with a new one following the instruction 
in Chapter 4, 

Replacement Procedure

. 

 

 

 

2-46 

[CONFIDENTIAL] 

 

TECRA R10 Maintenance Manual (960-708) 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands