manualshive.com logo in svg

Toshiba Tecra R10, Maintenance Manual

Share
Download
Toshiba Tecra R10 Maintenance Manual Download Page 256

4 Replacement Procedures 

4.12  ExpressCard slot/KILL SW HOL ASSY 

4.12  ExpressCard slot/KILL SW HOL ASSY 

Removing the ExpressCard slot/KILL SW HOL ASSY 

NOTE:   Before starting, make sure that a dummy card is removed. 

To remove the ExpressCard slot (EXPRESSCARD CONNECTOR WITH FPC) /KILL SW HOL 
ASSY, follow the steps below and refer to Figure 4-16 to 4-17. 

1.

 

Turn over the

 BASE ASSY

. 

2.

 

Remove the following 

screw

s securing the ExpressCard slot. 

•

 

M2.0

×

5B 

 S-THIN 

HEAD 

screw 

   

×

4 

3.

 

Remove the 

ExpressCard slot

 from the

 BASE ASSY

. 

4.

 

Peel off the 

INSU EXP SLOT UP

 from the 

ExpressCard slot

. 

 

ExpressCard slot  
(EXPRESSCARD CONNECTOR 
WITH FPC) 

M2.0x5B S-THIN HEAD

M2.0x5B S-THIN HEAD 

INSU EXP SLOT UP 

BASE ASSY 

Figure 4-16  Removing the ExpressCard slot 

4-30 

[CONFIDENTIAL] 

TECRA R10 Maintenance Manual (960-708) 

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands